Installer
- Firmware
- 1.0.0
- Status
- HARDWARE VERIFIED
- Hardware
- M-VAVE FM-1
- Package
- clatter-pocket-1.0.0-4d661dae.fwsc
- SHA-256
4d661dae903801385adc99abe3387474b059210f1c49037cef3ef1cacb6f5956- Prerequisite
- Official Open V14, from m-vave/fm1_open. Installed here only if the FM-1 needs it.
- Check
- Checking the package…
- This browser
- Not checked: this page needs JavaScript.
-
Prepare
- An M-VAVE FM-1 running stock V15 or official fm1_open firmware. If it runs stock V15, this page installs official Open first
- Chrome or Edge on a computer, with MIDI and SysEx allowed
- A USB data cable
- Anything you want to keep backed up. On official Open, M-VAVE's workbench backs up projects, samples and voices. Stock V15 has no project library for it to read
Close other MIDI software, keep the FM-1 powered throughout, and keep the recovery notes open in another tab.
-
Connect to the FM-1
Connect it by USB and switch it on. Your browser will ask to allow MIDI: allow it. This only asks the FM-1 what it is running. Nothing is written.
No device connected.
-
Stage 1: Prepare FM-1
Stock firmware detected
Official Open firmware requiredCLATTER Pocket installs over M-VAVE’s Open firmware. This is the official M-VAVE prerequisite, and there is nothing else to get: this page holds the exact firmware M-VAVE published.
- Firmware
- Official Open V14
- SHA-256
7e7b6d260163cdf9d716f7fab44f19be600edeffcd390de74370b83c917fd0c6
THIS REPLACES THE STOCK FIRMWARE
From stock, M-VAVE’s updater needs its forced mode. This is the route M-VAVE’s manual gives, and the same manual warns that it can erase projects and samples, stop the device starting, and need special tools to recover.
Stock V15 has no project library, so M-VAVE’s workbench cannot back up its projects. Keep anything you need another way first.
M-VAVE’s workbench can return the FM-1 to V15. That overwrites the voice banks with the 128 factory voices.
This page has installed one earlier release on one physical FM-1, from stock firmware.
Do not unplug, close this page or let the computer sleep. It finishes only when the FM-1 has restarted and reports official Open’s exact build.
Official Open is running, and verified by its build. Nothing else will be written until you confirm Stage 2. You can stop here: Open is a complete instrument, and M-VAVE’s workbench can set up its sample library.
-
Stage 2: Install CLATTER Pocket
Do not unplug, close this page or let the computer sleep until it says it has finished. It finishes only when the FM-1 has restarted and reports this exact build.
Keep this page open. Reconnect the same FM-1 and press Connect FM-1. If that does not work, follow the recovery notes below.
Now run the first hardware test. Follow FIRST-HARDWARE-TEST.md from First boot, and stop if any of its stop conditions happen.
Recovery
None of these routes has been tried with CLATTER Pocket on a device.
- Recovery procedure: restoring official firmware, and when to stop.
- Stop conditions: read these first.
- SAFE MODE: hold HOME 1.5 s after power-on. The engine stays off and the updater keeps running.
- M-VAVE's official workbench: the restore route. Keep it open in another tab.
- The FM-1 Firmware Hub's rescue guide: the community's tools, for other firmwares. Its OCT− USB rescue is not something CLATTER Pocket provides or has been tested with.
Why it is off
- This page needs JavaScript to read the release configuration. Installing stays off without it.